雙組份打膠機的注意事項分析
1.由于雙組份密封膠的固化需要一定時間，因此，已涂了雙組份密封膠的玻璃應水平輕輕搬動。
1. As the curing of two-component sealant takes a certain time, the glass coated with two-component sealant should be moved horizontally and gently.
2.a組、b組份膠應保持清潔，嚴防異物進入膠中。
2. The glue of group A and group B should be kept clean to prevent foreign matters from entering the glue.
3.在連續工作過程中，膠槍每次停止工作時間一般不得超過20分鐘，否則 中空雙組份打膠機，應用a組份膠沖出全部混合膠，直單一的a組份膠從槍口排出為止。
3. In the process of continuous operation, the stopping time of the glue gun should not exceed 20 minutes, otherwise, the hollow two-component glue machine should use component a glue to punch out all the mixed glue until the single component a glue is discharged from the muzzle of the gun.
4.高壓膠管不得---擠壓、彎曲，防止影響系統正常工作。
4. High pressure hose shall not be squeezed or bent to prevent affecting the normal operation of the system.
5.混膠器應經常保持暢通，以良好的出膠效果。如遇堵塞情況，可用---浸泡后清洗。建議每5組清洗一次。
5. The mixer should always be kept smooth to achieve good dispensing effect. In case of blockage, it can be cleaned after soaking. It is recommended to clean every 5 groups.
6.當膠槍長時間不用時（超過一周），應拆下槍體使用溶劑將膠槍和混膠器內的殘留膠體清洗干凈。
6. When the glue gun is not used for a long time (more than one week), the gun body should be removed and the residual colloid in the glue gun and mixer should be cleaned with solvent.
7.不同雙組份膠生產廠家所生產的膠內含雜質數量不同，根據實際情況清晰b組分的過濾網及單向止回閥 雙組份打膠機膠槍，建議每?jī)山M清洗一次。
7. The amount of impurities in the glue produced by different two-component glue manufacturers is different. According to the actual situation, it is recommended to clean the filter screen of component B and the glue gun of one-way check valve two-component glue machine every two groups.
8.任何因膠體固化所造成的膠槍、管路或整機的故障 雙組份打膠機配件，一律不在保修范圍之內。
8. Any failure of glue gun, pipeline or the whole machine caused by colloid curing is not included in the warranty.
9.定期給各泵的加油口加油，應油霧器內不斷油。
9. Oil the oil inlet of each pump regularly, and keep the oil in the oil mist.
上一篇：旋轉軸自動點膠可以提升圓形點膠效果嗎？
下一篇：平時應該如何保養中空玻璃生產線
