蜜桃av噜噜一区二区三区-蜜桃av麻豆av果冻传媒-蜜桃av亚洲精品一区二区-蜜桃bt天堂精品视频在线观看-蜜桃成人无码区免费视频网站-蜜桃福利视频

The pressure plate pump will be blocked during glue filling, which will reduce the amount of glue and affect the efficiency of glue filling, or cause the wrong proportion and affect the quality of glue filling. Or directly out of the glue, the machine can not be used. So how to prevent clogging? Now let's understand

1、混合管堵塞，造成這個現象的原因，有可能是中間短時間停止灌膠，沒有開啟防固化功能，膠水在混合管中表干了；也有可能是下班了，員工忘清洗混合管了，造成殘留在混合管中的膠水完全固化了，進而造成堵塞。防止這種堵塞的方法其實很簡單，員工短時間走開，比如十分鐘，二十分鐘，或者半個小時，就開啟防固化功能。如果是下班，中間時間比較長，直接開啟自動清洗功能，將混合管中的膠水清洗掉。

1. The mixing pipe is blocked. The reason for this phenomenon may be that the glue stops filling for a short time in the middle, and the anti curing function is not turned on, so the glue is dry in the mixing pipe. It may also be that the staff forgot to clean the mixing pipe after work, resulting in the glue remaining in the mixing pipe completely solidified, which leads to blockage. In fact, the way to prevent this kind of blockage is very simple. Employees can turn on the anti curing function in a short time, such as 10 minutes, 20 minutes, or half an hour. If it's off duty and the middle time is long, turn on the automatic cleaning function directly to clean the glue in the mixing pipe.

2、管道堵塞，造成這個現象的原因，有可能是膠水中的填料太多了，在管道中沉淀了。解決這個問題比較好的方法，就是更換比較好點的膠水。如果不想換膠水的話，就在漏斗上放一個過濾網，倒膠時，將膠水過濾一下。

2. The pipeline is blocked. The reason for this phenomenon may be that there are too many fillers in the glue, which precipitate in the pipeline. A better way to solve this problem is to replace the better glue. If you don't want to change the glue, put a filter on the funnel. When pouring the glue, filter the glue.

壓盤泵

Pressure plate pump

3、料桶堵塞，有些膠水長時間不用，在桶里面會干。有些客戶因為訂單原因，有可能一個月，或者兩三個月才灌一次膠。膠水長時間放在桶里面會干，所以針對這種情況，每次估算好要用的膠量，灌完后，將料桶清洗一下。

3. The material barrel is blocked. Some glue will dry in the barrel if it is not used for a long time. Some customers may only pour glue once a month or two or three months due to the order. Glue will dry in the bucket for a long time, so in view of this situation, estimate the amount of glue to be used each time, and clean the bucket after filling.

4、結晶堵塞，有些膠水固化劑會吸潮結晶造成堵塞，比如聚氨酯膠水。如果使用這種膠水的話，機器要用的比較勤會比較好，不要放置太久，因為聚氨酯膠水放久了會吸潮。如果一直用的話，膠水一直保持是新鮮的膠水，就能減少結晶。如果條件比較好的工廠，可以往料桶中充氮氣，氮氣是一種保護性氣體，解決膠水結晶的效果特別好。

4. Crystal blockage. Some glue curing agents will absorb moisture and crystal to cause blockage, such as polyurethane glue. If you use this kind of glue, it's better to use the machine more frequently, and don't put it too long, because polyurethane glue will absorb moisture. If you use it all the time, the glue will keep fresh, which can reduce the crystallization. If the conditions are better, you can fill the barrel with nitrogen. Nitrogen is a kind of protective gas, which can solve the problem of glue crystallization.